Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.
Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.
Blog Article
Do not ignore the forklift at the workplace. If the operation is not good, there will be serious mishaps in minutes, and there are numerous mishaps including forklifts.
Situation 1: The forklift freight obstructed the motorist's view, and the individual ahead might not be discovered, leading to a rolling crash.
Instance 2: In order to keep the equilibrium of the forklift when raising heavy products, the employees used their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an mishap.
Case 4: Forklift is speeding and surrender throughout a turn.
Situation 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not see the forklift.
Instance 6: The forklift raises the personnel illegally, the forklift vehicle driver does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift rolls over.
Instance 7: The forklift motorist did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift operation need to take notice of these matters ：.
Start.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be risk-free prior to starting.
3. When the forklift begins with a load, the vehicle driver must initially verify that the lots is steady and dependable.
4. The beginning should be slow-moving and stable.
Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When getting in and leaving the job site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After dumping, the fork should be reduced to the regular driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will trigger the lorry to lose lateral stability and tip over. .
5. When the forklift is downhill, it is strictly restricted to switch off the flame and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and have to maintain a particular safety distance from the vehicle in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry ought to be appropriately tilted back. The tons shall not be increased except when stacking or loading. .
8. The height of the load must not obstruct the vehicle driver's view. In unique scenarios, when the product impacts the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to depend on the fork to hold products and play a balancing duty. .
12. If troubles are discovered, they will be fixed and reported in a prompt manner, and they will never ever operate with illnesses or hide them.
packing and unloading.
1. When fork-loading things, the range between both forks must be adjusted as required to make the tons of both forks balanced and not skewed, and one side of the thing ought to protest the shelf. .
2. It is forbidden to collaborate with a single fork or make use of a fork top or draw. In special conditions, security indication need to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading things, the forklift should be stopped with the brake. .
4. The speed of the automobile ought to be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a Electric Forklift Truck for Warehouse fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork idea should not touch various other products or objects. The tons needs to be stabilized with very little back tilt of the gantry so that the tons does not glide in reverse. The mast can be slanted onward slightly when the tons is decreased to allow for simple placement of the lots and removal of the forks. .
6. It is forbidden to fork products at broadband and collide with difficult things with the fork head. .
7. When the forklift is working, it is forbidden for people to loaf the fork, so regarding avoid the collapse of the goods and hurt people. .
8. Straining is banned, and it is prohibited to utilize forks to raise employees to take part in high-altitude procedures to avoid high-altitude falling mishaps. .
9. It is not enabled to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to pick, turn pallet discharge.
Leaving .
1. It is restricted to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the parking brake deal with to dead or depress the emergency brake switch.
3. The engine is shut off and the power is cut Stand-on Electric Pallet Stacker off. (Except for special scenarios, such as the motorist does not leave the lorry's view and does not go beyond 1 min).
4. Eliminate the secret. .
Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance should be checked, and gas, lubing oil and air conditioning water must be included.
2. Inspect the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leak ought to also be examined and the seals need to be changed in time.
Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you come across somebody in front of you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not exceed 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m above the ground;.
5. The turning should not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Single fork operation is not permitted.
2. It is not allowed to raise the goods for cross country driving.
3. It is not allowed to get the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not permitted to use inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same size as the obstacle ought to be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844